TeknosPro KATTO Ceiling paint

Water-borne acrylate dispersion paint with especially flat finish, for dry spaces indoors. Without side sheen.

The product has been classified in Emission Classification of building materials to Group M1.

New or previously painted ceilings in spaces where especially high demands are placed on the appearance. Used on concrete, plaster, stopper, brick and construction boards.

Tehnilised andmed
Solids	About 36 % by volume
Volatile organic compound (VOC)	EU VOC limit value (kat A/a): 30 g/l. The product's VOC: max. 30 g/l.
Practical spreading rate	Previously painted surface Filler and wood fibre board Concrete and plastered surface 7 - 10 m²/l 5 - 8 m²/l 4 - 7 m²/l
Density	abt. 1.5 g/ml
Drying time at +23 °C / 50 % RH - dust free - overcoatable	after ½ hour after 2 hours The drying will be slowed down if the air is cool and/or humid.
Thinner, clean up	Water. Wash the equipment immediately after use with water.
Finish	Full-matt
Colours	White. Can be tinted with tinting pastes to light shades according to the Interior Colour Cards. The colour accuracy is not complete.
Washability and wear resistance	The painted surface resists slight wear. Wet scrub resistance, class 3 according to EN 13300 (ISO 11998).
Packages (availability varies by country)	2,7 L, 9 L, 18 L
SAFETY MARKINGS	See Safety Data Sheet.

Kasutusjuhendid
Surface preparation	Clean new surfaces from dust and dirt. Wash previously painted surfaces with RENSA SUPER paint cleaner. Matt down hard or gloss surfaces by sanding and thereafter remove the dust. Remove all of the old paint from the surfaces which have been painted with glue paint or lime wash. Spray filler ceilings, which are not waterproof, are recommended to be primed with solvent borne primer e.g. FUTURA 3 Adhesion primer. For smoothing of irregularities in the surface choose a suitable stopper from the TEKNOSPRO series. The dried stopper is sanded down and the dust removed.
Priming	Prime concrete, plaster, stopper, brick and building board surfaces with TEKNOSPRO POHJA Primer. Steel surfaces are primed with FERREX AQUA Anticorrosive paint.
Application	Before use stir the paint thoroughly. The paint is thinned with water when needed. Apply once or twice by brush, roller or spray. Suitable nozzle for airless spray is 0.017 - 0.021".
Application conditions	During the application and drying period the temperature of the ambient air, the surface and the paint shall be above +5 °C and the relative air humidity below 80 %. Good ventilation during the application and drying period quickens the drying process.
Maintenance instructions	The final forming of the paint film takes abt. 4 weeks under normal circumstances and after that the ultimate durability and hardness is reached. Before this the painted surface must be treated with care. Cleaning by moist wiping or with detergents damages the painted surface. Dry cleaning methods, such as careful wiping, brushing, vacuum cleaning etc., must be used for dirty surface.
Storage	Must not freeze.

Tootekirjeldustes esitatud andmed põhinevad laboratoorsetel katsetel ja toodete praktilisel kasutamisel. Kõik esitatud väärtused on suunavad ning olenevad muu hulgas toonist ja läikeastmest. Kuna me ei saa mõjutada värvi kasutus- või tööolusid, vastutame ainult värvi kvaliteedi eest ning tagame, et see vastab Teknose kvaliteedikinnitusele. Me ei vasta kahjude eest, mis tulenevad toote kasutamisest kasutusjuhendi või -otstarbe vastaselt. Meie koduleheküljelt www.teknos.com leiab ajakohased versioonid tootekirjeldustest, ohutusjuhenditest ja süsteemikirjeldustest.